3/22/2023 0 Comments Chimex brushBrush application direction for each layer must be perpendicular to each other. Mixture should be applied with a brush as 2 or 3 layers. Continue mixing until obtaining a homogenous mixture without any agglomerate (approximately 3-5 minutes). Liquid component B is poured into a clean container and mix at a low speed and then slowly added CHIMEX 125 powder component A. After the first coat of CHIMEX 125, sharp tips and horizontal/vertical joints which are suitable cracking should be chamfered with REPAMERK 1 repair mortar or PH 127 then second coat of CHIMEX 125 should be applied. Application surface has to be wetted and then waited until it becomes wet/dry. Big pores and cracks should be filled with REPAMERK 1 repair mortar. The application surface must be durable, clean and clean off materials which prevent bonding, such as dust, oil, rust and remove loose pieces. Resistant to chemicals and salt solutions in soil.Forms a jointless, seamless, permanent, water impermeable coating.It forms a water impermeable layer under screeds and ceramics with high adhesion performance and semi-elastic properties.In building foundation, retaining wall, indoor and outdoor for vertical and horizontal applications.In water pressure exposed areas like pools, water tanks and in wet volumes such as terrace, balcony, basement.Recommended 3 coats if required high protection.Cement-Acrylic Based, Two-Component Semi-Elastic Waterproofing Material - CHIMEX 125 CHIMEX 125 DescriptionĬHIMEX 125 is a cement-acrylic based, two-component, semi-elastic insulation material used on concrete and cement based plasters and applied from the inside and outside against leaking and surface water. Consumptionġ,25 - 1,5 kg/m² is applied on each layer. Also application should not be made in very hot, rainy or windy weathers. Ambient and substrate temperature should be between +5☌ to +35☌ during the application. It gains mechanical strength in 3 days, becomes waterproof in 7 days. Using mesh increases the reinforcing properties of the product. It is recommended to use a mesh between the layers. The surface must be protected from sunlight and prevented from drying quickly, for 3 days after the application of the second layer. In case the first layer is dry, the surface must be moisturized again before the application of the second layer. Second layer must be applied before the first layer is not completely dry. Minimum 5 - 6 hours and maximum 24 hours, must be waited after first coat application at +20☌. Brush application direction in each layer must be perpendicular to each other. Prepared CHIMEX 235 mixture is applied by brush or trowel as two or three layers. Wait for 3-5 minutes and mix again for approximately 30 seconds and becomes ready to use. Continue mixing for at least 3-5 minutes until a homogenous and uniform mixture is obtained. Pour liquid Part B into a clean mixing container and slowly add powder Part A while mixing with a 400-600 rpm mixer. The surface must be saturated with water and must be kept moist during the application. Holes that have water outflow must be filled with WATERSHOCK. Weak parts of the concrete must be repaired, plasters that are not well adhered must be removed, the surface must be flat and sound, static cracks on the building must be repaired with a plaster containing LATEX or REPAMERK 301. The application surface must be clear of materials which prevent bonding, such as oil, dust, paint, silicone, curing agents, detergents and paraffin wax. Can be used safely in drinking water tanks.Īpplication substrate must be dry, sound, mainly smooth, clean and fine pored.Provides seamless water isolation without joints.Not affected temperature changing after curing.Covers cracks up to 0.60 mm when applied as 2 mm thick and up to 1.20 mm when reinforced with waterproofing fiber mesh.High water vapour permeability allows the concrete to breathe. Highly resistant to carbon dioxide and chlorine ions.Forms a perfect isolation layer under ceramic and screed due to its flexibility and high bonding property.Provides highly performing water isolation.Resistant to negative and positive water pressure.To protect concrete from water, carbonation and salts.Wet areas such as bathroom, kitchen, balcony,.Irrigation channels, manholes, concrete pipes,.Isolation of terrace roofs (under the coverage),.Water tanks and swimming pools (under the coverage),.Groundwork isolation,retaining walls and basement isolation subject to slight vibrance,.Indoor and outdoor for horizontal and vertical applications,.Cement-Acrylic Based, Two Component, Flexible Waterproofing Material for Negative-Positive Application - CHIMEX 235 CHIMEX 235 DescriptionĬement and acrylic based, super elastic, two component, resistant to positive and negative water pressure waterproofing material with high crack bridging property.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |